This article applies to Yeastar MyPBX all models, N-Series Analog PBX and Yeastar VoIP gateways.
This article shall not apply to Yeastar S-Series VoIP PBX. Please refer to How to Log in SSH of Yeastar S-Series VoIP PBX.
How to Login via SSH
- Download the popular SSH tool PuTTy from the Internet.
- Enable SSH service on LAN Settings page or Service menu under LAN settings.
- Open the PuTTy, and configure the login IP, Port and Connection type(SSH).
- Host Name: IP address of the Yeastar device
- Port: default SSH port is 8022
- Username: root
- Password: ys123456
Note: when you enter the password, it's in invisible form that you can't see what you are inputting.
Command Mode and Asterisk Mode
Next we introduce you the important 2 modes in SSH interface: Command mode and Asterisk mode.
After you enter the SSH interface, it is the Command mode. In this mode, you can execute the Linux based commands, like ls, cd, route and so on.
To enter Asterisk mode, you can input asterisk -vvvvvvvvvr in Command mode. In this mode, you are able to execute the Asterisk based commands, like sip show peers, module reload and so on.
Hello! I cant login to ssh server on mypbx S20 with root/ys123456
HI For S20, the username is support and the password is iyeastar
this details i got it from one of the comment . please check this
Hi for the TA410 not access for ssh
John, for TA410, before you can access through SSH, you need to enable SSH on Service Center page, see below screenshot:
Hi, I have a TA2400 and configure ssh access and active port 8022, but still can not connect, and tells me there is no connection.
Hi William, I would reply you in the ticket.
I have a TA410 voip GW I accidentally black list access to the GW on port 8000 I can access the device through ssh
what commands I need to apply to disable the FW to log in again and fix it
I made a Youtube on how to use SSH on a Yeastar S20 to modify the configuration and customize the configuration to mute all participants of a conference. Its almost identical on the MyPBX. I'm logging into the S20 via SSH at about 6 minutes and 40 seconds.
Hello! I cant login to ssh server on MyPBX U100 with root/ys123456
Hello, at first I can ping my device MyPBX U100.
When I try to connect via SSH and it refuse to connect.
suddenly, I can not ping it anymore. Tried to hard reset but with no luck at all.
Hi Randy, You might be blacklisted by the PBX. Also the SSH service is not enabled. You can try to use the other computer or change your current computer IP address to access the web and enable ssh.
the thing is... I am just new to my work and the other guy didn't gave me the password. The device is in production so i can not reset the device into default config.
Any work around to reset the password?
we have a MYPBX U100 , A few days ago, when the power of the server room turned off, our central machine turned off and on.
After that we can no longer access the central panel, but it is possible to ping the IP of the central machine ، we can access the central device with SSH , IP Phones are working within the company , But we can not dial outside of the company , and we can not access the device panel.
we updated the Central operating system ( firmware ) with console cable , but problems are still not solved
Please help me how can i fix these problems
Here is a step by step video on how to SSH into a Yeastar S Series PBX https://www.youtube.com/watch?v=xwYq6w7P2rQ
Dear all I have same problem like Amir Hosseinzadeh, please can You give me some instructions what to do.
Everything works normaly, until one day when yeastar device was turned off and turned on, after that i cannot access over Web GuI.
I can access to device over SSH and over Console cable, also IP phones in company works good but I can not dial outside.
This is verry urgent.
Hi how SSH to yeastar tg400 with firmware's version 188.8.131.52 plz?
Hi I finally got access with iyeastar as password like this: ssh -p 8022 email@example.com
Then I found root user in /etc/passwd but it is not working with the web gui account password's admin, support password's and many others .....
Any suggestions plz?
The named root account on TG400 seems to be ls@yf. Any idea about ssh password?